2026年06月19日 11:55:44 来源：广东宏拓仪器科技有限公司 >> 进入该公司展台 阅读量：19
PAGE | CODE | VALUE | COMENTS | ||
dF Measurements Settings | diSP Renewal Frequency of density | ０ | STABLE | ||
１ | UNSTABLE | ||||
Err Decimal places which contain calculative tolerance | ０ | Tolerance decimal places Shown and Still | |||
１ | Tolerance more than ±２ Flashing | ||||
２ | Tolerance more than ±２ Deleted | ||||
AL-ｔ Set Measuring time in Air/Water | ０ | 0.0 Sec／0.0 Sec ※Press key, and get a result immediately. | |||
１ | 0．0 Sec／1．8 Sec | ||||
２ | 1．8 Sec／4．2 Sec | ||||
３ | 4．2 Sec／7．8 Sec | ||||
４ | 7．8 Sec／16．2 Sec | ||||
Lqd Setting Density of a liquid Mediuim | ０ | Prohibited | |||
１ | Permitted | ||||
ｄAtA Data Output (in auto-printing） | ０ | Output aerial Weight and Density | |||
１ | Output collectively aerial Weight, underwater Weight, Density and Volume | ||||
Func Balance and Output settings | Poff Auto power-off | ０ | OFF | ||
１ | ON | ||||
St-b Stability indication range | ０ | Stable mark appears within ±0.5g per 0.5 Sec | |||
１ | Stable mark appears within ±1.0g per 0.5 Sec | ||||
２ | Stable mark appears within ±2.0g per 0.5 Sec | ||||
trc Zero trucking | ０ | OFF | |||
１ | ON | ||||
CP Comparator Mode | ０ | OFF | |||
１ | ON | ||||
bEP Buzzer sound ※Optional kit needed | ― | ― | |||
― | ― | ||||
― | ― | ||||
Prt Data output Mode | ０ | Commａnd mode/ Stream mode（Output the same data repeatedly) | |||
１ | Commａnd mode/ B key mode | ||||
２ | Commａnd mode/ Auto-printing after finishing measurement | ||||
PUSE Output data interval | ０ | No interval（ Set this when sending data to a computer） | |||
１ | 1.6 sec interval | ||||
２ | 3.2 sec interval （Set this when using Printer: 8121B） | ||||
inFo GLP Output Format | ０ | OFF | |||
１ | Output data when using Printer: 8121B | ||||
２ | Output data when using general-purpose computer | ||||
bPS Baud Rate | ０ | 2400ｂｐｓ | |||
１ | 4800ｂｐｓ | ||||
２ | 9600ｂｐｓ | ||||
btPr Data bit / Parity bit | ０ | ７bit EVEN | |||
１ | ７bit ODD | ||||
２ | ７bit NON | ||||
LtUP Display's Backlight | ０ | Always OFF | |||
１ | Turn off in 3 seconds after stable mark appears | ||||
２ | Turn off in 10 seconds after stable mark appears | ||||
３ | Turn off in 30 seconds after stable mark appears | ||||
４ | Turn off in 60 seconds after stable mark appears | ||||
５ | Always ON | ||||
oP ｄ Optional Setting | R１ A R１ b R２ A R２ b R３ A R３ b | R1 | Optional Set a specific Gravity of main metal | ||
R１ | Optional Set a specific Gravity of alloyed metal | ||||
R2 | Optional NO.2 Set a specific Gravity of main metal | ||||
R2 | Optional NO.2 Set a specific Gravity of alloyed metal | ||||
R3 | Optional NO.3 Set a specific Gravity of main metal | ||||
R3 | Optional NO.3 Set a specific Gravity of alloyed metal | ||||
CP Hi | Comparator Max Density | ||||
CP Lo | Comparator Min Density | 出荷時設定００００００となっています | |||
id | Setting GLP output ID number | ||||
